Why is my UPS flashing?
This indicates that the UPS is performing a Self-Test of the battery. If it fails the test, the red Replace Battery LED will illuminate. This LED will remain illuminated until the unit passes a Self-Test.
How do I reset my APC UPS?
Reset APC UPS
- Turn off UPS via control panel on front of unit.
- Unplug UPS from the wall.
- Disconnect the battery. This is a plug on the rear of the unit labeled “ BATTERY CONNECTOR” (You may hear an audible click from the UPS)
- Reconnect the battery.
- Turn on UPS.
- Plug UPS into the wall.
- Test for original failing condition.
Why is my UPS blinking green?
Flashes green in rapid succession. The battery has been completely discharged while the Back-UPS is on battery, the UPS will shut down. None – AC power is restored – AC is not restored within 32 seconds – The Back-UPS is turned off.
Why is my APC battery backup flashing red and green?
The constant alert one and flashing red/green lights can indicate a disconnected or failed battery.
When should I replace my APC battery?
The battery is by far the most vulnerable and failure-prone part of your UPS. If you have your UPS long enough, you will probably have battery problems. Once every six months to a year or so you should recalibrate your UPS’s battery sensor, and once every several years you will have to replace the batteries.
How do you hard reset a UPS?
The Brain Dead procedure performs a hard reset of the Smart-Ups microprocessor….Cold Start:
- Turn off and unplug the Smart-UPS from wall.
- Press and hold the power button (labeled “”I/TEST”” on legacy non-LCD screen units) on the front of the UPS until you hear a LONG beep.
- Let go DURING the long beep.
How do I know if UPS is charging?
You can tell if the UPS is charging by installing the software that came with it (or downloadable from APC’s website) and plugging in the USB cable that comes with the UPS. Running your computer through a brand new UPS is not a problem.
What happens if you overload a UPS?
What happens if the UPS is overloaded, for example, if the protected equipment and/or load draws more current than it can provide. The UPS transfers the load to bypass (for a few minutes) until the overload condition is reversed. If the overload condition continues, some UPS models automatically shut down.
What is red light in APC UPS?
Over temperature On Battery – UPS has exceeded the over temperature threshold. Note: The UPS will beep and the red LED will illuminate till the internal temperature reaches the normal range for 5 minutes before the UPS shuts down.
Why is UPS not working?
Be sure the line cord is connected. Be sure each circuit breaker is in the On position, or replace the fuse if needed. If this occurs repeatedly, contact an authorized service provider. Check the UPS LEDs to be sure a battery or site wiring problem has not occurred.
Why are the LEDs on my Smart UPS flashing?
Green On Line LED: flashing Yellow On Battery LED: on solid. This indicates that the UPS is performing a Self-Test of the battery. If the Self-Test passes, the green On-Line LED will go on solid while the yellow On Battery LED will go off. If it fails the test, the red Replace Battery LED will illuminate.
Why does my ups battery light go on and off?
This indicates that the UPS is performing a Self-Test of the battery. If the Self-Test passes, the green On-Line LED will go on solid while the yellow On Battery LED will go off. If it fails the test, the red Replace Battery LED will illuminate. This LED will remain illuminated until the unit passes a Self-Test.
What does the red light on my ups mean?
If it fails the test, the red Replace Battery LED will illuminate. This LED will remain illuminated until the unit passes a Self-Test. This indicates that the UPS has entered “”sleep mode”” where the UPS will turn off its output power in an effort to conserve battery power.
What does the Green on line indicator on my ups mean?
If the UPS passes the Self-Test, the green On Line indicator will be lit and solid. If it fails the test, the red Replace Battery indicator will be lit as well as the green On Line LED. If the UPS fails the test and the unit is still in warranty (3 years from date of purchase), contact APC’s Technical Support for further troubleshooting.
