What is the torque for a pressure plate?
Tighten all bolts evenly, ¼ turn at a time in a crisscross pattern until pressure plate is completely drawn-up to the flywheel. Final torque to: 25 – 28 ft/lbs.
What is the torque setting for the bolts?
US Recommended Bolt Torque
| Size | Recommended Torque | |
|---|---|---|
| Grade 2 | 18-8 S/S | |
| #10* | – | 31.7 |
| 1/4″ | 4 | 7.8 |
| 5/16″ | 8 | 11.8 |
Can you reuse pressure plate bolts?
If the bolts haven’t been over-torqued and stretched you can reuse them.
What’s the torque on a clutch?
The torque capacity of the clutch is the amount of torque that can be transmitted by the clutch when it’s slipping or when it’s fully closed. The torque capacity of a clutch depends on a series of factors: total area of the friction surface. friction coefficient.
What is a pressure plate?
: a plate in an automobile dry disk clutch that is pressed against the flywheel to transmit propulsion torque to the wheels.
What size are LS Flexplate bolts?
11mm x 1.5
Chevrolet Performance LS Flywheel/Flexplate Bolt Thread: 11mm x 1.5.
What is the torque for 1/4 bolt?
ASTM A449 / SAE Grade 5*
| Bolt Size | TPI | Tightening Torque (ft lbs) |
|---|---|---|
| Plain | ||
| 1⁄4 | 20 | 8 |
| 5⁄16 | 18 | 17 |
| 3⁄8 | 16 | 31 |
What is the torque setting?
This setting lets you control the torque or turning power of the drill driver. The higher the torque (number on the torque ring), the more ‘power’ the drill driver produces and the deeper the screw can be driven into the workpiece.
Can you reuse flywheel bolts?
Flywheel bolts are reusable as long as they are in good condition. Clean them off, apply red loctite.
What is the torque capacity?
What are the torque specs for a tdiclub?
Strut retainer bolt and self-locking nut (bolt that goes through spindle, holding the strut in place; replace hex bolt. Bolt point must point to the front of vehicle): 60 Nm plus an additional 90* turn; Never less than 90* Dec 10, 2003
What are the torque specs for a new beetle?
Strut retainer bolt and self-locking nut (bolt that goes through spindle, holding the strut in place; replace hex bolt. Bolt point must point to the front of vehicle): 60 Nm plus an additional 90* turn; Never less than 90* Dec 10, 2003 Texas Hill Country black 1999 New Beetle Jul 17, 2000 Staten Island (The Dump) 2002 Golf
How big is a 1.9L TDI ALH engine?
9L TDI ALH Location Size Ft-lbs Nm Replace Notes Bell housing to engine block 60 81 Bell housing to oil pan 16mm 33 45 Cam Bearing Cap 13mm 15 20 Cam Sprocket 19mm 33 45 Connecting rod bolts 22 30 Yes +1/4 Turn, oiled threads and contact surfaces Crank shaft bolt 88 119 Yes +90 degrees CV Axle M10 59 80 CV Axle M8 30 41
What kind of torque does a golf 02m have?
Austin, TX/Chapel Hill, NC ’00 Golf 02M, ’10 Golf 02E, ’02 UTE 02M – Dog bone (aka) Rear Transmission Mount (aka) Pendulum Support… -transmission (manual) drain/fill plugs 18 ftlb. Strut retainer bolt and self-locking nut (bolt that goes through spindle, holding the strut in place; replace hex bolt.
