What is the most common spindle nut?
There are several manufacturers offering one-piece spindle nut systems. The two most common are the Axilok® nut by Metform (see Figure 1) and the PRO- TORQ® nut by Stemco (see Figure 2). Each of these systems has a specific installation procedure required by the manufacturer to set wheel bearing end-play.
Can you reuse spindle nut?
IF the nut comes OFF clean, then yeah, you can probably reuse it. I have reused some before. However, if the stub of cv shaft sticking out is all rusted up/threads corroded, then you will likely damage the threads on the nut when you remove it. In that case, I would NOT reuse it.
What size is the spindle nut?
The Nut is a 1 inch nut with 14 threads. The socket or wrench needed for this is 1-1/2 inch.
Are axle nuts universal?
Universally fits all roller skate trucks (most current skates use the more common 8mm) including Dominion, Sure-Grip, PowerDyne, Riedell, Pacer, Roller Derby and all others.
Are all spindle nuts the same size?
Front spindle nuts are the same size for wire wheel or disc wheel hubs, they should be 1 1/8″. The rear wheel hub nuts are 1 5/16″.
How tight should spindle nuts be?
The nut on the spindle should be tightened until snug, with no side-to-side play in the hub and then backed off slightly, about maybe a 1/8 of a turn.
What size is the spindle nut on a Dexter Axle?
| 165931 | SPINDLE NUT,7/8″-14 FINE THREAD |
|---|---|
| 6-96 | SPINDLE NUT, 1 1/2″ ID FINE THREAD x 2 1/4″ OD |
| 6-84 | SPINDLE NUT, 1 3/4″ FINE THREAD |
| 90623 | SPINDLE NUT, 1 1/2″ FINE THREAD (CASTLE NUT) |
| 6-114 | SPINDLE NUT, 2 5/8″ FINE THREAD (INNER FOR D200) |
How do you measure axle nut size?
Stretch the tape measure across the nut’s diameter to the flat-side directly across from the one your pulling from. If the nut is metric, count the number of lines on the tape measure to find the measurement. If you count 9 lines, the size is a 9-mm (millimeter) nut.
Are bicycle wheel nuts a standard size?
If it’s 5/16″ at 26 threads per inch then an M8-1.00 nut may fit since 25.4 tpi is very close to 26 tpi and 7.9mm diameter is very close to 8mm. First try your LBS, take the wheel with you….8 Answers.
| Nominal Thread Size | Example of Bicycle Uses |
|---|---|
| 5/16 inch x 24 tpi | Front hubs, solid axle, less expensive bikes |
What kind of socket do I need for Dana 44?
The hubs are manual and the differential is 100% stock, so the issue is the socket, not the diff. It’s a quality made socket, but the advertising is miss leading. Best socket to use with Dana 44 and similar that use a Pin-lock on the inner 4 lug nut.
How big are the spindle nuts on a 1990 Ford F-250?
Ok, so I have a 1990 Ford F-250 with a Dana 44 front differential. The engine is 460, and trans is the 4OD, but that doesn’t matter. This socket does not fit the spindle nuts on my differential, despite being advertised as doing so. The nuts are maybe a 1/4 inch larger in diameter than the socket.
How big are the spindle nuts on a trans?
The engine is 460, and trans is the 4OD, but that doesn’t matter. This socket does not fit the spindle nuts on my differential, despite being advertised as doing so. The nuts are maybe a 1/4 inch larger in diameter than the socket.
What kind of wrench do I need for spindle nut?
Use with 1/2-Inch square drive tool. Wrench fits spindle nut on Chevy, 1/2-ton GMC, Blazer, Bronco, Bronco 11, Ranger, Explorer, 1/2- and 3/4-ton Ford, spline-type hub, IHC 1100 series and 1/2-ton Dodge vehicles. Will work on Ford vehicles with ratcheting type lock nuts on front axle..-Octagon Spindle Nut Wrench 3-7/8-Inch.
