What are the dimensions of a standard fireplace?
The average fireplace has the following dimensions: An opening that’s between 24-36 inches wide, 24-29 inches high, and 16 inches deep. On average, the distance between the hearth and the damper is about 37 inches. The fireplace’s rear firebox is generally between 11-19 inches wide, with a height of 14 inches.
How wide is a standard fireplace hearth?
The front of the hearth needs to extend to a minimum of 20 inches, and the side areas need to extend to 12 inches. The recommended thickness for larger fireplace hearths remains the same.
How wide are most fireplaces?
The standard size of a fireplace is anywhere from 2 – 3 feet wide, 24 – 29 inches high, and always about 16 inches deep. Of course, the opening could vary depending on your style and design ideas, as well as where you are locating the fireplace.
How big is a masonry fireplace?
2111.7 Firebox Dimensions The firebox of a concrete or masonry fireplace shall have a minimum depth of 20 inches (508 mm). The throat shall be not less than 8 inches (203 mm) above the fireplace opening.
How do I choose the right size fireplace?
To calculate fireplace size, measure the width, length, and height of your room in inches. Multiply these three numbers together to determine the room’s volume, then multiply that number by four, which will give you a close minimum heat output. You can select an appropriate size with the original dimensions.
How deep should my fireplace be?
A typical 3-foot-wide fireplace opening should only be 29 inches tall. The firebox depth should be 16 inches (not including the thickness of the decorative brick that faces the fireplace). The distance from the floor of the fireplace to the bottom of the damper should be 37 inches.
What is the average hearth height?
12” to 18”
The most common hearth heights are from 12” to 18”. If you’re tall (over six-feet), choose a higher hearth size. The same thing goes for sitting on the hearth, if you’re shorter, choose a lower hearth height.
How much wider Should fireplace be than TV?
In our experience, the fireplace should be a little wider (6-8 inches) than the TV. This allows the wall to frame the TV, while offering sleek lines for the edges of the fireplace. Having more space beyond the TV edges can sometimes make the TV look too small for the wall it is on.
How wide is a brick fireplace?
Firebox Dimensions and Chimney Heights
| Fireplace Opening Width | 24″ | 36″ |
|---|---|---|
| Firebox Depth | 16″ | 16″ |
| Rear Firebox Width | 11″ | 23″ |
| Rear Firebox Wall Vertical Height | 14″ | 14″ |
| Nominal Flue Size | 8×12 | 12×12 |
How far away from a fireplace should a TV be?
The minimum distance between a fireplace and a TV is 20 inches with a mantel. Also, allow at least a 7-8 inch clearance from the top of the mantel to the TV. To avoid straining when watching TV, place the TV a maximum of 65 inches off the ground.
How big is a standard fireplace opening?
The standard fireplace opening averages between 24 – 36 inches wide, 24 – 29 inches high, and about 16 inches deep. The distance from the hearth to the fireplace damper should be about 37 inches. The rear of the firebox should be 11 – 19 inches wide and right at 14 inches high.
How big does a standard fire brick have to be?
Fire brick must be a minimum thickness of one and one-eighth inch (1-1/8”). The STANDARD fireplace is available in three sizes: thirty-six inch (36”), forty-two inch (42”) and forty-six inch (46”).
What should the dimensions of a fireplace be?
Fireplace Design & Dimensions 1 Sides of fireplace must pinch in towards back 2 Back wall of fireplace must be straight up for first 12 inches 3 Back wall must slope towards front for remainder of height 4 Width and height of opening MUST come from table below 5 Smoke shelf up above fireplace must be sized correctly – see below More
How are the dimensions of a brick measured?
Standard brick sizes vary from country to country, with dimensions written as depth x height x length (D x H x L). Standard brick dimensions may be expressed in either imperial units, in terms of inches, or metric units, as millimeters.
What kind of bricks are used in fireplaces?
Facing, or face brick, is most commonly used to make a good impression in places with high visibility, such as fireplaces and entries. Bricks come in different sizes, and brick lengths can vary.
