Is 1T better than 2T?

Games performance – the influence of the Command Rate (1T vs 2T) The average performance increase is ~3.5% for 1T Command Rate over 2T. Let’s perform another quick test run to see what are the benefits of 3733 MHz vs 3600 MHz using the same CL settings and Infinity Fabric divider set to 1:1.

What is the difference between 1T and 2T?

1t means that the controller sends the command on one clock cycle, 2t means it sends it for two clock cycles.

What is 1T command rate?

The command rate determines whether a chip select can be executed in a single clock or whether it needs two or more clocks. Typical DDR2 memory runs at a command rate of 2T, but a 1T command rate can yield as much of a gain in performance as any other adjustment.

What is 2T memory?

The 2T Command BIOS feature allows you to select the delay between the assertion of the Chip Select signal till the time the memory controller starts sending commands to the memory bank. When this feature is disabled, the memory controller will only insert a command delay of one clock cycle or 1T.

What size is 1T?

Should I disable gear down mode?

Power Down Mode doesn’t necessarily improve performance, but it can improve memory stability. I would leave this disabled if you are at all overclocking your RAM.

Is 1T and 12 months the same?

Yes. The difference between 1T and 12 months is the way it’s made. For example if the 12 month old is not walking yet it’s best to get 12 months it’s easier to slide a shirt off the shoulder and down where as 1T is not made like that.

What is a 1T?

When talking about data storage, systems are often measured in terabytes, but most files seen on a daily basis are stored in gigabytes or megabytes. 1 TB equals 1,000 gigabytes (GB) or 1,000,000 megabytes (MB).

What is the best FSB DRAM ratio?

By default, FSB speed and memory are usually set to a 1:1 ratio, meaning that increasing FSB speed (by overclocking) increases memory speed by the same amount. Normally system memory is not built for overclocking and thus may not be able to take the level of overclocking that the processor or motherboard can achieve.

What is command rate on RAM?

Command Rate is the number of cycles between the memory controller selecting and issuing any command to a RAM chip. Copying, reading, and writing, it makes a difference for everything. It is an important timing for real-world performance.

Are 12 month and 1T the same?

Which is faster DDR3-1600 or ddr-1333?

This is the speed of the RAM Clearly DDR3-1600 is able to run faster than DDR-1333. But thats only the modules ability not what the system is running its memory bus speed at. Your MacBook was designed for PC3-10600 DDR3 SDRAM, its best to stick with what Apple expects.

Which is faster a 1T or 2t memory?

1T is typically ~4-5% faster than the same memory/speeds at 2T if I recall correctly… this was a big topic back when DDR2 was brand new. At least when I was benching my main rig awhile back I had a ~6% delta in 3dmark overall scores (~7% on CPU, and SuperPi) when running 1T vs. 2T.

Which is better DDR3 or PC3L Ram?

PC3L RAM will work in a PC3 based system as it will run at the standard voltage and will inter-operate with PC3 RAM within the system. 12800 MB/s (DDR3-1600) Vs 10600 MB/s (DDR3-1333) This is the speed of the RAM Clearly DDR3-1600 is able to run faster than DDR-1333.

Can you use 12800s RAM on a PC3?

The 12800S RAM The answer, unfortunately is not definitive. Usually, yes. But, because of no strict standardization enforcement it may not work. I’d say better to order DDR3 if that is what originally came with your motherboard. I bought 3 PC3L RAM different brands all did not work on my PC3 system.