How do you fix a UL code on a Whirlpool Cabrio washer?
Your washer is off balance or the load is unbalanced The washer is running a load-balance correction routine. Allow the washer to continue. If the dial is flashing and the washer has stopped, redistribute the load, close the lid, and press START/PAUSE.
How do you reset a Whirlpool Cabrio washer?
Press the Start Stop button once. Rotate the dial until Rinse, Wash, and Stop light illuminate. Turn the washer off and unplug it for 10 seconds. Finally, turn on the washer and it should now be reset.
How do I read a whirlpool error code?
Error Codes in my Whirlpool Front Load Washer
| Error Code | Error |
|---|---|
| rL or F34 | Items were detected in the washer during the Clean Washer cycle. |
| Sud or Sd | There are too many suds in the washing machine. |
| F5 E2 | The door is not locking properly. |
| F7 E1 | Indicates a motor speed sensing error, |
Why is my Whirlpool Cabrio washer not draining?
Check the washer’s discharge hose if the water fails to drain from the washtub. Look for any kinks in the Cabrio washer’s discharge hose that could stop the water from draining. Straightening the hose ensures proper draining. Test the drain pump to ensure it has not failed if the washer still will not drain.
Why does my Whirlpool washer keep getting off balance?
Laundry caught below the tub or between the agitator and the inner tub can cause the washer to operate off balance with every load. The problem can be anything: a penny that worked its way out of a pocket, a button that fell off a shirt or a wayward sock or other article of clothing.
How do you clear the fault code on a Whirlpool Cabrio?
First press PAUSE/CANCEL once to clear the Fault code from the Cabrio display. If code appears again put it through an automatic diagnostic cycle while you enjoy a nice soothing cup of tea. (Watch The Cabrio Diagnostics Video); This will reveal any stored Fault codes.
How do you troubleshoot a Whirlpool Cabrio washer?
Clean all contact areas on the lid and the washer. Try unplugging the washer to allow the control panel to reset. Plug the washer back in and see if the problem resolves. If the door sounds like it is engaging, but doesn’t, it is time to run a diagnostic test.
What does FH mean on a whirlpool washer?
An F20 or FH error code indicates a water supply problem. Here are some common issues: Both hot and cold water must be connected and turned on. Water inlet hoses kinked.
How do you clear the error code on a whirlpool top load washer?
System error code. Press START/PAUSE once to clear the code, then press START/PAUSE again to restart washer. If the code doesn’t clear, Contact Us or Schedule Service Online. Hot and cold inlet hoses have been installed incorrectly (reversed).
What does ul code mean on a whirlpool washer?
Whirlpool Cabrio Washer Error UL. The Cabrio Washer UL error code stands for un-balanced or off-balanced load which means the control has recognized the the tub is off balance during the spin cycle. This code will be shown as the washer control tries to balance out the load if its successful Cabrio Washer Error UL will clear from the display,…
What does LD mean on Whirlpool Cabrio washing machine?
Whirlpool Cabrio Washer Error LD. The Cabrio Washer LD error code stands for Long Drain which means the control has recognized the water in the tub is not draining fast enough during the cycle.
What does LF mean on the Whirlpool Cabrio washing machine?
Whirlpool Cabrio washer with error code LF. This error means Long Fill (LF). It basically means that if the machine has not filled after 10 minutes then it goes into this error condition. First thing to do is make sure the taps are turned on.
