How do I view IPMP in Solaris 11?

Create the IPMP group “ipmp0”. Create the interfaces net1 and net2 to be used in the IPMP group. To check the status of individual interfaces in the IPMP group.

What is IPMP in Solaris 11?

IP network multipathing (IPMP) provides a mechanism for building redundant network interfaces to guard against failures with network interfaces, cables, switches, or other networking hardware. Each interface is assigned a static test IP address, which is used by Solaris to verify the operational state of the interface.

How to change IP Solaris 11?

Configuring the IP address

  1. Step 1 : Set the NCP. We would set the NCP to DefaultFixed profile in order to configure the IP address manually.
  2. Step 2 : Check the link status. The command “dladm show-dev” does not work in Solaris 11.
  3. Step 3 : Create a new interface.
  4. Step 4 : Creating IP address.

How to remove IP address in Solaris 11?

How to Delete IP Addresses From an IPMP Interface

  1. Become the root role.
  2. Determine the IP addresses that you want to remove. Display a list of data addresses as follows: # ipadm show-addr ipmp-interface.
  3. Remove the IP addresses from an IPMP group. Remove data addresses as follows: # ipadm delete-addr addrobj.

How do I view Ipmp on Solaris 10?

Add the IP address in /etc/hosts and specify the netmask value in /etc/netmasks like below one. Plumb the interfaces which you are going to use for new IP address. check the status in “ifconfig” output. Configure IP on Primary interface and add the interfaces to IPMP group with your own group name.

What does Ipmp stand for?

IPMP

Acronym Definition
IPMP International Project Management Program
IPMP Intellectual Property Management & Protection (MPEG-4)
IPMP Internet Protocol Multi-Pathing (Sun Microsystems)
IPMP Institute for Participatory Management and Planning

How do I set a default route in Solaris 11?

Creating Persistent (Static) Routes

  1. Use the route command with the –p option to persistently add a route: # route -p add default ip-address.
  2. Display the currently active routes on a system by using the netstat command with the following options: # netstat -rn.

How do I find my IP address on Solaris?

Monitoring IP Interfaces and Addresses

  1. To obtain interface information, use ipadm show-if.
  2. To obtain address information, use ipadm show-addr.
  3. To obtain information about a specific interface property, use ipadm show-ifprop.
  4. To obtain information about a specific address property, use ipadm show-addrprop.

How do I set a default route in Solaris?

How to Change The Default Route or Gateway on Solaris

  1. Edit /etc/defaultrouter. -This configuration will apply after next reboot. [root@SolarisServer ~]# vi /etc/defaultrouter 192.168.2.1.
  2. Run the following command to delete and add the default route. -This will apply the configuration with immediate effect.

How do I create a route in Solaris 11?

How does IPMP work in Oracle Solaris 11?

When compared with the IPMP configuration in Oracle Solaris 10, Oracle Solaris 11 groups the IP interfaces into a virtual IP interface (for example, ipmp0). The virtual IP interface serves all of the data IP addresses, while test addresses that are used for probe-based failure detection are assigned to an underlying interface, such as net0.

How does the virtual IP interface work in Solaris?

The virtual IP interface serves all of the data IP addresses, while test addresses that are used for probe-based failure detection are assigned to an underlying interface, such as net0. With IPMP, you can assign two or more NICs to a failover group.

How to improve network performance in Oracle Solaris 11.1?

IPMP in Oracle Solaris – Managing Oracle Solaris 11.1 Network Performance This book explains how to further configure datalinks and IP interfaces to improve network performance, such as combining links into aggregations, using IP multipathing groups, using integrated load balancing, and other methods. JavaScript is required to for searching.

Can a single IP interface become an IPMP group?

In compliance with the second rule, the single IP interface that connects to the second LAN cannot become a member of that IPMP group. No IPMP configuration is required for the single IP interface. However, you can configure the single interface into an IPMP group to monitor the interface’s availability.