Does OSHA apply to offshore platforms?

The Outer Continental Shelf Lands Act (OCSLA)(43 U.S.C. 1331 et. seq.) has conferred the U.S. Coast Guard, the Department of the Interior (Minerals Management Service), and OSHA with the statutory authority to promulgate regulations which address working conditions on offshore drilling platforms.

Are landing platforms for fixed ladders required by OSHA?

3-1992, American National Standard for ladders — fixed — safety requirements, indicates that landing platforms are not required on fixed ladders with cages less than 50 feet in length, and landing platforms are required at every 50-foot interval on fixed ladders with cages extending a maximum unbroken length of 50 …

Does OSHA require stair landings?

Reply: OSHA’s Fixed Industrial Stairs standard, 29 CFR 1910.24, does not require stair landings and/or intermediate platforms along the path for stairways that are not used for fire exit purposes.

What is a platform OSHA?

Platform means a walking-working surface that is elevated above the surrounding area. Portable ladder means a ladder that can readily be moved or carried, and usually consists of side rails joined at intervals by steps, rungs, or cleats.

Where does OSHA not have jurisdiction?

Reich requesting information about coverage and posting requirements under the Occupational Safety and Health Act of 1970 (the Act). The Occupational Safety and Health Administration (OSHA) does not have jurisdiction over State and local government employees (firemen and policemen).

Does OSHA apply outside the United States?

The Occupational Safety and Health Act, and therefore the OSHA Recordkeeping Regulation, apply only within the jurisdictional boundaries of the United States as defined in Section 4(a) of the Act.

At what height does OSHA require a ladder?

Fixed ladders: fall protection must be provided for employees climbing or working on fixed ladders above 24 feet. 29 CFR 1926.1053(a)(19) states that fall protection must be provided whenever the length of climb on a fixed ladder equals or exceeds 24 feet.

How high can stairs go without a landing?

[This means there is no door swinging out over the stairway – Ed.] A flight of stairs shall not have a vertical rise greater than 12 feet (3658 mm) between floor levels or landings. [This means that if the height or rise between two floors is more than 12 feet you need an intermediate stairway landing – Ed.]

How high can a platform be without a step OSHA?

Vertical clearance above any stair tread to any overhead obstruction is at least 6 feet, 8 inches (203 cm), as measured from the leading edge of the tread.

What is considered a working platform?

A work platform is essentially any elevated platform used as a place of work. There is no specific height requirement of a platform before it becomes a work platform. If a platform is elevated only one inch for a specific job task, that platform would be a work platform.

How big of a landing platform do I need for a ladder?

If the normal step-across distance exceeds 12 inches (30 cm), a landing platform shall be provided to reduce the distance to the specified limit. Fixed ladders without cages or wells shall have a clear width to the nearest permanent object of at least 15 inches (38 cm) on each side of the centerline of the ladder.

How big does a platform need to be for fall protection?

Platforms used with fixed ladders provide a horizontal surface of at least 24 inches by 30 inches (61 cm by 76 cm). Note to paragraph (g): Section 1910.28 establishes the requirements that employers must follow on the use of cages and wells as a means of fall protection. Figure D-14 — Clearances for Fixed Ladders in Wells.

Can a caged ladder be cited by OSHA?

Thus, the caged ladders on the stack which exceed 30 feet are technically in violation, however, since they comply with both the OSHA proposed rule and the current consensus standard for fixed industrial ladders and the level of safety is not diminished, they will not be cited.

How often does a chimney need a landing platform?

(3) A landing platform shall be provided at least every 50 feet within the length of climb. We have been advised by several prominent chimney/steel stack design companies/consultants that OSHA adopts ANSI A14.3 and ASME STS-1-1992 as their governing guides since OSHA Part 1910.27 takes exception to chimneys.