Can you control temperature on towel rail?

If you want to have extra control over your heating, you can install thermostatic radiator valves (TRVs) on your heated towel rails. Thermostatic Radiator Valves don’t control the temperature of your towel rail, instead they control when the heated towel rail switches on or off depending on the heat in the room.

Can I put TRV on bathroom radiator?

It is not a good idea to fit TRVs to your bathroom radiator, simply because the TRV will not work properly. TRVs have their own thermostat to control the temperature of the room. So, the heat caused from having a hot shower or bath can confuse the TRV or shut it down completely.

What are the two valves on a towel radiator for?

One valve accounts for the amount of hot water that enters the radiator. The other valve, referred to as the lockshield valve, balances the system by regulating how much heat the radiator gives off.

What valves go on a towel radiator?

Straight valves should be used when the inlets are at the bottom of the towel rail and the pipes are protruding from the floor. Angled valves will be needed if the water needs to be diverted at a 90-degree angle. This is often the case when pipes and valve inlets are situated at the side of the radiator.

Do I need a TRV on my radiator?

However, while TRVs can, technically, be installed on all radiators, it’s usually a good idea to leave one radiator without a TRV and permanently switched on. Ideally, this should either be a bathroom, which would usually benefit from permanent heat, or the room with the thermostat in it.

Do heated towel rails have thermostats?

These type electric towel rails have a silicon sealed wire inside the bars/tubes which heats the towel rail. A final note on these dry electric towel rails is that they do not have any built in thermostats which you can control the heat.

Should I have a TRV in the bathroom?

Bathrooms: A TRV No-No Don’t make the mistake of installing a thermostatic radiator valve in your bathroom, as the heat produced by your shower or bath will wreak havoc with the TRV’s thermostat. Instead of preventing the condensation that often hinders bathrooms, the TRV will shut off and do nothing.

Do you need a TRV on a towel rail?

However, it’s always recommended to have at least one radiator in your home to have manual valves, without a TRV. It’s common practise for this radiator (or towel rail) to be in the bathroom. The reason one radiator in your home needs to be TRV-free is as a safety mechanism.

What do valves on bottom of towel rail do?

Radiator valves are an essential part of how a radiator, or a heated towel rail, functions. They control the flow of water through the pipes and ensure that your radiator heats up effectively and efficiently – keeping you, your home and everyone in it, nice and comfortable and warm.

Can you fit a TRV to a towel rail?

In theory, it’s completely possible to install a thermostatic radiator valve on a heated towel rail and in theory the process would be the same exactly as described above. However, it’s always recommended to have at least one radiator in your home to have manual valves, without a TRV.

Where is the valve on a heated towel rail?

Discovering where the valve inlets on your radiator are is fairly straight-forward and is defined primarily by the kind of radiator or heated towel rail that you have. With a heated towel rail, for example, you will normally find that the inlet position is located underneath at the bottom.

Should you put a TRV on a towel rail?

Why TRVs are not always recommended on towel rails However, it’s always recommended to have at least one radiator in your home to have manual valves, without a TRV. The reason one radiator in your home needs to be TRV-free is as a safety mechanism.

Do you need a TRV on a radiator?

However, it’s always recommended to have at least one radiator in your home to have manual valves, without a TRV. It’s common practise for this radiator (or towel rail) to be in the bathroom. The reason one radiator in your home needs to be TRV-free is as a safety mechanism.

Can a towel radiator be fitted with a thermostatic valve?

Im aiming to install a Towel Radiator in the bathroom, and am wondering wether to plumb a Thermostatic Valve to it. We originally sized the radiator up with a view to fitting it with standard chrome valves (cheap & matching – unlike most TRVs)

Can a TRV be fitted to a bathroom Rad?

Some engineers – in the uk – do not recommend fitting a TRV to the bathroom rad as a constant flow is required around the CH system for safety reasons. This is what I was told by a Gas Safe Engineer.

How does a thermostatic valve work on a radiator?

If a room is cold, the valve will detect this low temperature and allow more hot water into the radiator. Once the temperature in the room reaches the desired temperature, the valve will automatically close and stop any more hot water entering the radiator.