What gears are available for a Dana 60?
New ratios available for the Dana 44 and 60 axles include 4.56, 4.88, and 5.13, adding to existing ratios of the Dana 60 axle that range from 3.54 to 7.17 and the Dana 44 axle that range from 3.07 to 5.13.
Are all Dana 60 gears the same?
All Dana 60 housings use the exact same carriers whether high pinion or low pinion. The high pinions have the same gear break as low pinions. The thick gears are available so that you do not have to change carriers.
What is the lowest gear ratio for Dana 60?
7.17 is the lowest aftermarket gears you can purchase for a dana 60 rear.
Does a Dana 60 have a crush sleeve?
Dana 60s do NOT use crush sleeves. All D60s use shims to get the correct pinion depth.
What is a Dana 60 reverse rotation?
There is no such thing as a reverse rotation Dana 60 axle, front or rear. They all turn the same way. The front high pinion axle has reverse cut gears, but it still turns the same way.
What is the highest gear ratio for Dana 60?
There is no such gear as 3.08 for a dana 60. The tallest ratio out there is in the 3.30 range. I would not go any taller than 3.54’s. That gear will give you plenty of umph and keep the engine in it’s sweet spot for cruising.
How do I identify a Dana 60 carrier?
To distinguish a 4.10 and down carrier (called a 3-series carrier) from a 4.56 and up carrier (called a 4-series carrier) you need to measure the distance from the face where the ring gear sits, to the end of the carrier, as shown in the following pic – labelled dimension “A”.
Is Dana 60 limited slip?
The passenger car version of the Dana 60 came equipped with the Mopar “Powr-Lok” semi-float limited-slip differential option from 1966 to ’69. The Powr-Lok differential used 30-spline axles. The axle bearings, seals and retainer packages are interchangeable.
What does the crush sleeve do?
Moderator. It’s not for bearing preload it’s like a lock washer for the pinion nut. It springs back around . 015 and keeps a constant pressure on the pinion nut through the front pinion bearings inner race and yoke.
Which is the best spider gear set for a Dana 44?
Yukon YPKD44-S-30-JK Yukon replacement standard open spider gear kit for Dana 44, non-Rubicon JK with 30 spline axles. Yukon YPKD44-T/L-30 Yukon replacement spider gear kit for Dana 44 trac loc posi, 30 spline. Yukon YPKD50-P-30 Yukon positraction internals for Dana 50 Dura Grip posi, 30 spline.
What kind of gears do Dana 60 axles have?
Description: DANA SPICER 707175X : Fits Dana 60 axle with 4.56 gears or numerically higher. This case has ABS provision 2 – 7/16 Tall. Description: Dana 60 Detroit package deal. D60 35 Spline Detroit- DET225S-29A or DET225S-29B DANA 60 Gear (Standard or Rev.) Master Install Kit Also add Chromoly shafts, U-Joints, and hubs at…
What kind of gear set does a Dana S135 use?
Yukon YPKDS135-S-36 Yukon replacement standard open spider gear kit for Dana S135 with 36 spline axles. Yukon YPKF8.8-T/L-31 Yukon spider gear kit for Ford 8.8″, 31 spline, Trac Loc posi.
What are the install kits for Dana 60?
DANA 60 MASTER INSTALL KITS, PINION INSTALL KITS, MINI INSTALL KITS, INDIVIDUAL BEARINGS, SHIMS, SEALS, PINION NUT AND OTHER SMALL PARTS. DANA 60 KNUCKLES AND HEAVY DUTY STEERING KITS.
